Need instructions for Mavic 2 series

I've successfully downgraded my Mavic 2 Pro's firmware to 01.00.0100 and patched it with "Remove NFZ" in NLD Mod Client.

After patching and then restarting, the white LED flashes once confirming that NFZ patch is active. As there are no instructions specifically for the Mavic 2 series, may I know are there anymore steps or instructions that I need to follow to completely remove NFZ?

One more question please. In the "Flight Controller" page in NLD Mod Client, all the options in "Other" section at the bottom right hand corner are not selectable including "Disable No Fly Zones" and I have already unlocked my drone under "Lock/Unlock Device" in this "Flight Controller" page as well. If I am not able to select "Disable No Fly Zones", then how am I going to disable it?

Thanks in advance.

Why can't my  "Flight Controller" page open?  Mavic Pro 2

I downgraded my NLD version to 1.00.000 (which I did without wanting), everything went smoothly, and then I went back to NLD again at 1.00.100 without any problem. Perhaps this is the way I discovered by chance. Vertical speed changed, but the NFZ did not work. I also tried with DJI GO 4 in airplane mode and also with Litchi too. So at the moment, the only effect is vertical speed, but at the expense of a much older version of the software. I guess we'll have adjustments soon.
Thanks to the team for work!

My experience: downgrade, patch. No settings or other things to perform, NFZ are disabled and I can fly the bird in red spots on the go.

Thought I should post an update for Mavic 2 series owners. :-)

As mentioned in my original post about a week back, I successfully downgraded to .0100 and this was what I did.

Using DJI Assistant 2, I downgraded my Mavic 2 Pro from .0300 to .0200. Tried several times but I was unable to downgrade it further to .0100.

Then I switched to NLD Mod Client and successfully downgraded it from .0200 to .0100. After that, I relaunched NLD Mod Client and rebooted my Mavic 2 Pro. From here, I patched it with "Remove NFZ" in NLD Mod Client.

After patching and then restarting, the white LED under my Mavic 2 Pro flashes once confirming that NFZ patch is active.

I believe that's all I did. I did a test flight with three batteries last night and my Mavic 2 was able to take off in a NFZ which I was unable to do so before. But most importantly, please fly responsibly! :-)

Thought I should mention this too. There was this one time when I turned on my remote controller and my Mavic 2 Pro and when they were connected, I saw this warning message on my remote controller saying I am unable to take off because I am in a NFZ for just a few seconds but then it went off the screen and I was able to take off. Again, please fly responsibly! :-)

Tested Return To Home (RTH) several times too and it worked.

Btw, my remote controller firmware version is the latest; .0400.

Hope this helps some of you guys here. :-)

Today I upgraded to .0400(RC&AC  and go4 v4.3.16) before using NLD,
1:using DJI Assistant 2 to downgraded  Mavic 2 Pro from .0400 to .0200.
2:using NLD Mod Client to downgraded to .0100.
3:click on remove NFZ then apply NFZ Patch----- no NFZ limitation works.
I'm sure that I can fly in NFZ area,but mavic2 side vision sensors was disable cannot be turn on.
Thanks to Paul's guideline.

NONE of these steps have worked for me. 8-(

wyl wrote:

Glad that my post helped.

Btw, the side sensors only work in active track and tripod mode even with DJI official firmware.

In my opinion, it makes no sense to use DJI Asistens to lower from 0.400 to 0100. I did it with NLD and everything went without a problem, and NFZ was the first time.

There's no specific instructions for the Mavic 2 series but only to downgrade to 01.00.0100. This was why I tried to downgrade with DJI Assistant 2. In the process, discovered that DJI Assistant 2 can only downgrade to 01.00.0200.

I'm sure the above helps too for people who are wondering why they are stuck at 01.00.0200 with DJI Assistant 2.